<ul>
<li>Tow-behind</li>
<li>650-bushel (22.9-cu m) capacity</li>
<li>Fill all four tanks as quickly as 20 minutes*</li>
<li>Calibrate rate in half the time</li>
</ul>
*Fill time compared to 1910 550 TBH based on Internal John Deere testing.

C650 Air Cart

Agriculture

<ul>
<li>AutoConnect™ deck compatible for deck attach/detach in seconds</li>
<li>Cab or Open Station configuration available</li>
<li>PowrReverser™ or E-hydro transmission with Twin Touch™ pedals</li>
</ul>

3039R Compact Utility Tractor

Key Features
<ul>
<li>Engine Power: 125 hp</li>
<li>Easy to use transmission</li>
<li>NEW integrated technologies (JDLink™, AutoTrac™)</li>
<li>NEW optional suspended front axle</li>
</ul>

5125r-tractor

5125R Utility Tractor

Key Features
<ul>
<li>Engine Power: 115 hp</li>
<li>Easy to use transmission</li>
<li>NEW integrated technologies (JDLink™, AutoTrac™)</li>
<li>NEW optional suspended front axle</li>
</ul>

5115r-tractor

5115R Utility Tractor

Key Features
<ul>
<li>Engine Power: 100 hp</li>
<li>Easy to use transmission</li>
<li>NEW integrated technologies (JDLink™, AutoTrac™)</li>
<li>NEW optional suspended front axle</li>
</ul>

5100r-tractor

5100R Utility Tractor

Key Features
<ul>
<li>Engine Power: 90 hp</li>
<li>Easy to use transmission</li>
<li>NEW integrated technologies (JDLink™, AutoTrac™)</li>
<li>NEW optional suspended front axle</li>
</ul>

5090r-tractor

5090R Utility Tractor

Key Features
<ul>
<li>PowrQuad PLUS 16F/16R or Powr8 32F/16R transmission options</li>
<li>Climate-controlled cab</li>
<li>Hitch lift capacity of 6,970 lbs. with an option of 7,860 lbs.</li>
<li>Integrated AutoTrac™ guidance</li>
</ul>

5115m-powrquad-pluspowr8-utility-tractor

5115M Utility Tractor

<div class="key_features">Key Features
<ul>
<li>PowrQuad PLUS 16F/16R or Powr8 32F/16R transmission options</li>
<li>Climate-controlled cab</li>
<li>Hitch lift capacity of 6,970 lbs. with an option of 7,860 lbs.</li>
<li>Integrated AutoTrac™ guidance</li>
</ul>
</div>

5100m-powrquad-pluspowr8-utility-tractor

5100M Utility Tractor

<ul>
<li>PowrQuad PLUS 16F/16R or Powr8 32F/16R transmission options</li>
<li>Climate-controlled cab</li>
<li>Hitch lift capacity of 6,970 lbs. with an option of 7,860 lbs.</li>
<li>Integrated AutoTrac™ guidance</li>
</ul>

5090m-powrquad-pluspowr8-utility-tractor

5090M Utility Tractor

<ul>
<li>2WD or MFWD</li>
<li>5-year Powertrain warranty*</li>
<li>Available in premium cab, standard cab or open operator station</li>
<li>No Regen required</li>
</ul>

5067E Utility Tractors

<div class="key_features">
<ul>
<li>67 engine hp</li>
<li>Best-in-class visibility</li>
<li>Thick comfortable seat</li>
<li>5-Year Powertrain Warranty</li>
</ul>
</div>
<a class="no_show_m btn btn-larger btn-primary btn-product btn-raq various" href="https://www.agprocompanies.com/new-equipment/agriculture/tractors/5-series-tractors/small-frame/5065e-utility-tractor/#inquire">REQUEST A QUOTE</a>

5065e-utility-tractor

5065E Utility Tractor

John Deere

<ul>
<li>Mow up to 2 acres</li>
<li>23 HP* (17 kW) V-Twin engine</li>
<li>48- and 54-in. (122- and 137 cm) forged Accel Deep™ Mower Decks available</li>
<li>20-inch (50.8 cm) high-back custom-tailored seat with arm rests</li>
<li>LED lights, floor mat, front bumper, rear hitch, covered storage come standard</li>
<li>3-year/200-hour bumper-to-bumper warranty**</li>
</ul>

Z330R ZTrak™ Mower with 48-in. Deck

<ul>
<li>Mow up to 2 acres</li>
<li>23 HP* (17 kW) V-Twin engine</li>
<li>48- and 54-in. (122- and 137 cm) forged Accel Deep™ Mower Decks available</li>
<li>20-inch (50.8 cm) high-back custom-tailored seat and standard rear hitch</li>
<li>3-year/200-hour bumper-to-bumper warranty**</li>
</ul>

Z330M ZTrak™ Mower with 48-in. Deck

<ul>
<li>48-inch (122-cm) floating mower deck</li>
<li>Powerful 19 hp (14.2 kW) V-twin engine</li>
<li>Self-propelled hydrostatic drive system</li>
<li>Easy-to-use controls for operator comfort and convenience</li>
</ul>

W48R Commercial Walk-Behind Mower

Rippers

Semi-Mounted Rotary Rakes

Horizontal Fold Disc Mowers

Front Mounted Disc Mowers

Professional-Duty Roadside Mowers

Vari-Manager Series

Vertical Fold Disc Mowers

Landscape and Estate Shredders

Trailed Round Bale Wrappers

Trailed Square Bale Wrappers

Seeding Equipment

<ul>
<li>Choice of auger or conveyor</li>
<li>Stationary single-shoot manifold</li>
<li>In-line drive system transfers power efficiently</li>
<li>New 550-bushel grain tank capacity on tow-behind models</li>
</ul>

1910 Tow-Behind Air Commodity Cart

<ul>
<li>Productive seedbox capacities</li>
<li>Double-disk furrow openers</li>
<li>Reliable, durable convoluted seed tubes</li>
<li>Seed metering system</li>
</ul>

1520 Integral Drill

<ul>
<li>Quick Change Blade enhancement of the ProSeries™ Opener reduces change time by up to 45%1</li>
<li>Wide variety of working widths and row spacings</li>
<li>Latest John Deere technologies</li>
<li>Premium Lighting and easier access to meters </li>
</ul>

N542C Air Drill Central Commodity System (CCS™)

<ul>
<li>Quick Change Blade enhancement of the ProSeries™ Opener reduces change time by up to 45%1</li>
<li>Electric drive with Section Control</li>
<li>Wide variety of working widths and row spacings </li>
<li>Premium Lighting and easier access to meters </li>
</ul>

N536C Air Drill Central Commodity System (CCS™)

<ul>
<li>Positive depth control features and options</li>
<li>Choice of ground-engaging openers</li>
<li>Longer machine life with flexible frame</li>
<li>Remote height sensors</li>
</ul>

1830 Air Hoe Drill

<ul>
<li>Productive Seedbox capacities</li>
<li>Easy-to-read seed level indicator</li>
<li>Accurate fertilizer metering</li>
<li>Box drill acremeter</li>
</ul>

1590 No-Till Drill

<ul>
<li>Accurate seed metering capability</li>
<li>Wide variety of working widths and row spacings</li>
<li>Ground drive system with dual-range sprocket</li>
<li>Durable mainframe and wings</li>
</ul>

1990 Central Commodity System (CCS™)

<ul>
<li>850-bushel (30-cu m) capacity</li>
<li>170 acres (69 ha) per fill</li>
<li>Calibrate rate in half the time</li>
</ul>

C850 Air Cart

<ul>
<li>Patented active hydraulic down-pressure system</li>
<li>Double-disk furrow openers</li>
<li>Seedbox capacities</li>
<li>Grass seed attachment</li>
</ul>

455 Front-Folding Grain Drill

View Product Brochure

Harvesting equipment, cutters, shredders, hay &amp; forage equipment, planting &amp; seeding equipment, sprayers and tillage equipment

BALR: Farm Equipment

<div>
 
 The more frequently calibration is completed, the more accurate a seeder will be. A number of variables, including product weight and changing climate conditions throughout the day, will have an effect on any volumetric metering system; with the John Deere ActiveCal system, calibration can be done from the cab of the tractor, while seeding, to minimize the variation in product metering.
  
 The process to calibrate the implement starts with the Gen 4 4600 CommandCenter™ Display in the work setup page, where the operator defines product types, rates and selects meter rollers. Based on information entered into the work setup page, a preconfigured meter displacement value (MDV) will populate per meter. An initial manual calibration will give the most accurate MDV to start with. However, the preconfigured MDV will be a good starting point for growers who do not wish to manually calibrate.
  
 The operator engages ActiveCal while stationary by selecting the button on the screen and then begins seeding. When enough product has been metered out, typically after about 3.2 to 4.9 ha (8 to 12 acres), the Gen 4 CommandCenter will prompt the operator to stop when convenient to do so. At that time, the data points are calculated and a new MDV with percent difference is displayed on screen. The operator can accept or reject the new MDV. If accepted, the system automatically calibrates to the new MDV. If rejected, the system continues at the previously calibrated numbers.
 
 </div>

John Deere ActiveCal™ system

<div>
 
 The durable display on the side of the cart will make filling and calibration easier than before. Selecting the menu button on the far left will take the grower to the main menu where they can select:
 <ul>
 <li>Tank: shows product weight and tank fill level</li>
 <li>Meter calibration: preform a bag calibration without going back and forth to the cab to make inputs on the Gen 4 CommandCenter™ display</li>
 <li>Info: shows display and software information</li>
 <li>Tank pressure: shows the differential pressure between the tank and the meter for each individual tank</li>
 <li>Monitor settings: allows the customer to adjust the brightness of the display</li>
 </ul>
 
 Tank weights and bin level will be shown on the first screen when the display is powered on. Navigating from one tank weight to another will be done by pressing the left and right arrow buttons.
 
 Meter calibration can be done cart side. To select the tank or tanks that need to be calibrated, press the display button that matches the icon below the respective tank on the screen.
 
 The digital screen replaces the mechanical tank pressure gauges on previous carts.
 </div>

Cart side display functions

<div>
 
 With RelativeFlow Blockage sensing, operators can see the flow of both seed and fertilizer from inside the tractor cab. Sensors on all secondary hoses monitor the relative product flow row to row, giving you a better view of the flow rate of both seed and fertilizer from the cart to the opener from inside your tractor cab. This technology can help you identify any problems before a potential blockage occurs.
  
 RelativeFlow Blockage is available in all run configurations on the following models (all widths):  
 <ul>
 <li>H500</li>
 <li>H500F</li>
 <li>P500</li>
 <li>P600</li>
 <li>N500</li>
 <li>N500F</li>
 <li>N500C</li>
 <li>730LL</li>
 </ul>
  
 RelativeFlow Blockage is compatible with hydraulic drive carts: model year 2014 and newer 1910, all 19,381.5-L (550-bu) 1910 Carts, and C650 and C850 Air Carts.
  
 Below are the Gen 4 display screens for the blockage monitoring system. For complete details and information, see the owner’s manual.
 
 The RelativeFlow Blockage sensing chart shows the amount of flow through each sensor on the selected tower. Sensitivity for the blockage system can be adjusted if desired, as shown below.
 
 Blockage warning sensitivity allows the producer to set and change the sensitivity of the sensors to meet their preferences and varying crop/fertilizer types. Increasing the sensitivity means the system is more likely to show a false blockage, while less sensitivity means the system is more likely to miss a blockage.
  
 Multiple run-page alarm behavior options are available for selection.
 
 Below are the Gen 4 display screens for the blockage monitoring system on the N500C.
  
 For complete details and information reference, the owner’s manual.
 
 The SeedStar™ system run page displays the five major run settings. Clicking on any of the tiles will take an operator to that specific page (shown below).
 
 
 Blockage alarm delays can be set up by clicking on the advanced settings button from the blockage set-up screen.
 <ul>
 <li>A blockage delay is how long a blockage should occur before an alarm is sounded.</li>
 <li>The blockage alarm reminder is how often the alarm should sound when a blockage occurs.</li>
 <li>The meter on delay is the time from when the meter is turned on until the blockage sensor should start monitoring for blockage.</li>
 <li>The meter off delay is the time from when the meter is turned off until the blockage sensor should start monitoring to verify no flow.</li>
 </ul>
 For more detailed information, see the owner’s manual.
  
 Air tools with RelativeFlow Blockage are not compatible with 1910 air carts with ground drive.
  
 </div>

Confidence in rates from row to row with RelativeFlow™ Blockage sensing

<div>
 
 SectionCommand is an effective, integrated, exclusive John Deere solution that reduces costly overlaps and skips that can waste seed and fertilizer, while offering more consistent fields that improve the potential of your yield and your bottom line.
  
 Thanks to individual meter sections that control commodity flow, you can maintain the right application rates and row-to-row accuracy. This helps stimulate even crop emergence during the growing season and promotes consistent crop maturity at harvest. SectionCommand controls output from all meters on the cart up to eight sections.
  
 Owner benefits include:
 <ul>
 <li>Improved consistency of crop maturity at harvest</li>
 <li>Improved consistency during emergence and growing season</li>
 <li>Reduced seed input cost</li>
 <li>Reduced fertilizer input cost</li>
 <li>Increased time between fills due to input savings</li>
 </ul>
 SectionCommand is base equipment with optional deduct on all John Deere 1910 and C-Series Air Carts. Each tank and meter will receive SectionCommand components. A two-tank cart will control sections out of both tanks, a three-tank cart will control sections out of all three tanks, and the C-Series Air Carts will control sections out of all four tanks. SectionCommand is also available as an attachment for field conversion (AFC) for all 1910 hydraulic drive carts. See <a href="http://element-si-staging.azurewebsites.net/docs/sales/salesmanual/en_NA/seeding/attachments/metering/1910_cart/sectioncommand_field_conversion_kit.html">AFC kit story</a> for more information.
  
 SectionCommand controls seed and fertilizer output by closing and opening gates on the bottom side of the meter. When the gates are open, commodity is metered out, and when closed, commodity stays and continues to rotate within the meter. The meter stays full at all times so immediately when the gate opens, the commodity can flow into the primaries and out to the tool. Since each meter section has its own gate, application rates and row-to-row accuracy are not compromised. The gates are utilized to control commodity output on all sections. Once the last gate needs closed, the entire meter will stop turning, stopping product flow.
 
 When commanded, electric over-hydraulic solenoids engage actuators to instantaneously close the gate for the needed section. The actuators are powered via hydraulics from the same circuit as the hydraulic drive motors. When power is cut, oil is diverted to retract the actuators and open the gates. The retraction is both powered and spring assisted, so it will always default to the seeding position. The oil from SectionCommand drains back through the fan motor case drain line and is coupled with an accumulator on the valve block to provide extra drainage capacity.
 
 SectionCommand incorporates gate detection, which gives producers the satisfaction of knowing the gates are in position as commanded. Magnets on the back side of the gates are used in close proximity to the gate detection sensors to determine if the gates are open or closed. Should a gate not be in the commanded position, an alarm will alert the operator of the gate(s) in question. The blockage warning system works in conjunction with SectionCommand to give further confidence whether a given section is seeding or not when commanded.
 
 For maximum performance, SectionCommand should be controlled through John Deere Section Control. Coupling SectionCommand with John Deere Section Control provides the ultimate in precision seeding and productivity. If a Section Control activation is held by the producer, that same activation can be utilized for SectionCommand.
  
 SectionCommand introduces the orange roller, which has the same number of flutes and spacing as the blue roller, but shorter flutes. It is for use only with SectionCommand when seeding seeds larger than 6 mm (0.25 in.) in diameter (soybeans, chick peas, etc.). The orange roller is not for use with cereal grains or fertilizer.
 
 <h5>SectionCommand equalizer</h5>
 
 Due to the varying lengths of product delivery hose used across the drill, SectionCommand has a built-in equalizer feature to ensure consistent product delivery across the width of the drill when entering and exiting headlands. The software allows the producer to set the on/off product delivery times separately for the outermost opener and the innermost opener on the drill. Product delivery times are inputted for each tank on the cart, and the software creates a time delay for actuation of the gates.
  
 Please see the <a href="https://johndeeredealers.mc.wg1.kontiki.com/global2/content?moid=da147de5-4047-4b78-97e9-f9743089625a">Using SectionCommand</a> video for more information.
 
 </div>

Take command of every acre and every input with SectionCommand™ system

<div>
 
 A meter cartridge at each tank effectively meters seed or fertilizer into the primary manifold. Air carries the material to the secondary distributor for delivery to the openers on the seeding tool.
  
 Meters are contained in a cartridge for convenient removal and are color coded for easy identification.
 
 A manual half-width disconnect is incorporated into the meter system:
 <ul>
 <li>
 <div>
 Allows one-half of the metering system to be manually shut off for irregular shaped headlands, point rows, etc. on mechanical drive carts.
 </div></li>
 <li>Allows the meter cartridge to be removed with material still in the tank(s).</li>
 <li>Allows tanks to be emptied with meter and primary manifold in place.</li>
 </ul>
 
 On the C-Series Air Carts, an electric actuator controls product flow from the tank to the meter housing:
 <ul>
 <li>Allows complete shut off of product flow with little effort</li>
 <li>Allows the meter cartridge to be removed with material still in the tank(s)</li>
 <li>Allows tanks to be emptied with meter and primary manifold in place</li>
 </ul>
 </div>

Meter seed accurately with confidence

<div>
 
 The C650 Air Carts come standard with the wireless-controlled hydraulic conveyance system with a low-profile hopper. Maneuvering the conveyor can be done from the wireless conveyor remote or the remote tethered to the cart. With five pivot points on the arm, all tanks can be filled from one spot. The pivot points also allow the conveyor to be easily positioned and moved when filling from a seed tender.
  
 This conveyor moves up to 3524 L (100 bu) of product in a minute with a 48.26-cm (19-in.) belt inside the 30.5-cm (12-in.) tube. By moving the hopper under meter, the conveyor can be used for clean out on each tank as well.
 
 The shut-off switches on the conveyor are located at the bottom of the tube, above the hopper and at the top of the conveyor near the spout. Filling at night is easy with the light-emitting diode (LED) 900-lumen lights on the cart and conveyor conveniently placed to illuminate each meter, the stairway and platform.
 </div>

Wireless-controlled hydraulic conveyance system with low-profile hopper

<div>
 
 The tow-behind C650 Air Cart comes equipped with rear dual Firestone® 800/70R38 SFT tires and front single Firestone 900/75R32 CFO tires. The tow-between C650 comes equipped with rear dual Firestone IF850/75R42 CFO tires. These are high-floatation, low-compaction solutions. The Firestone tires run at an inflation pressure of 131 kPa (19 psi). Super flexion tire (SFT) technology means that the sidewalls on the tire are developed with additional reinforcement and superior rubber compounds, which enables the tires to run at a very low pressure while under higher loads without damaging the sidewalls. By running at lower pressure, the tire can flex its sidewalls and squat, allowing for a much wider footprint and improving floatation.
  
  
 To see how the tire pressures on the C-Series Air Carts compare to the 1910 Commodity Carts, please reference the <a href="http://element-si-staging.azurewebsites.net/docs/sales/salesmanual/media_files/NA/seeding/1910_c850_c650_tire_pressure_guide.xlsx">tire pressure guide</a>.
 
 Mitas is a trademark of Mitas, Akciova Spolecnost Corporation. Firestone is a trademark of Bridgestone Americas Tire Operations, LLC.
 </div>

Floatation and Compaction

<div>
 
 The total capacity of the C650 is 22,905 L (650 bu), measured by conveying product into the tank. The front tank is dedicated for low rate applications and holds 1762 L (50 bu). The remaining three tanks in order of front to rear are 9162 L (260 bu), 4581 L (130 bu), and 7400 L (210 bu).
  
 John Deere air cart tanks are solid molded polymer, known for superior corrosion resistance compared to steel while providing semi translucency allowing for visual verification of product level in day-time operation. Each tank is mounted in a cradle frame to eliminate interference between each other. The polymer material does not require weldments like on steel tanks. Weldments on steel tanks are prone to failure over time as the metal is fatigued under stress.
  
 The improved top bevel design on tanks allow for greater capacity and meets the 22,905 L (650 bu) capacity without the need for shoveling product into the corners while conveyor filling.
  
 Each tank has a wide, single opening, which means it is easy for access for the conveyor and entry to the tank. Inside each tank is a ladder for cleanout access. Ladders in the tanks have been designed so that material cannot build up on steps. Top rails have been capped and sloped to ensure product sheds from the surface. When cleaning out the cart, the tanks slope steeply at bottom for product to flow easily and each tank is accessible for fill and cleanout with the conveyor.
  
 Tanks come equipped with digital pressure sensor, ultrasonic bin level sensing, and camera-ready harnesses mounted from the factory.
 </div>

Tank capacity and design

<div>
 
 Monitoring product levels in tanks has never been easier with the camera-ready feature of C-Series Air Carts. The carts come pre-wired to accept a camera in each tank and one off the rear of the machine. Monitoring product levels is especially reassuring when product levels are low. Cameras also provide the operator with visibility behind the cart when traveling down the road or backing into a shed.
 
 For C-Series Air Carts, the producer can add up to five Voyager® or CabCAM™ cameras while also using a Generation 4 4600 CommandCenter™ Display or 4640 Universal Display. If the producer wants to view more than four cameras, a producer-purchased camera display will be needed.
  
 NOTE: Generation 4 displays support Voyager and CabCAM cameras.
  
 While the C-Series Air Carts come pre-wired to adapt cameras, additional harnesses are necessary for connecting to the tractor, and a tool overlay harness will be needed.  Please use the part numbers below for configuring an existing, compatible tool.
 
 <table class="table table-striped table-bordered">
 <tbody>
 <tr>
 <td width="141"> Air cart model/configuration</td>
 <td width="107">  Display</td>
 <td width="66">  Display harness</td>
 <td width="104">Display harness to air cart/seeder or tool overlay harness</td>
 <td width="60">Seeding tool overlay harness</td>
 <td width="107">  CabCAM adapter</td>
 <td width="201">  Notes</td>
 </tr>
 <tr>
 <td width="141">C650/C850Tow Behind</td>
 <td width="107">4600 CommandCenter</td>
 <td width="66">AA93727 (oneper camera) connected behind rear cab cover</td>
 <td width="104">AA94316</td>
 <td width="60">AA94564</td>
 <td width="107">Not required for Gen 4 display</td>
 <td width="201">Up to four CabCAM or Voyager cameras can be installed (four in tank, one rear view)</td>
 </tr>
 <tr>
 <td width="141">C650/C850Tow Behind</td>
 <td width="107">4640 Universal Display</td>
 <td width="66">SWTY268456</td>
 <td width="104">AA94316</td>
 <td width="60">AA94564</td>
 <td width="107">Not required for Gen 4 display</td>
 <td width="201">Up to four CabCAM or Voyager cameras can be installed (four in tank, one rear view)</td>
 </tr>
 <tr>
 <td width="141">C650Tow Between</td>
 <td width="107">4600 CommandCenter</td>
 <td width="66">AA93727 (one per camera) connected behind rear cab cover</td>
 <td width="104">AA94316</td>
 <td width="60"> </td>
 <td width="107">Not required for Gen 4 display</td>
 <td width="201">Up to four CabCAM or Voyager cameras can be installed (four in tank, one rear view)</td>
 </tr>
 <tr>
 <td width="141">C650Tow Between</td>
 <td width="107">4640 Universal Display</td>
 <td width="66">SWTY268456</td>
 <td width="104">AA94316</td>
 <td width="60">AA97386</td>
 <td width="107">Not required for Gen 4 display</td>
 <td width="201">Up to four CabCAM or Voyager cameras can be installed (four in tank, one rear view)</td>
 </tr>
 </tbody>
 </table>
  
  
 CabCAM is a trademark of ATI Products, Inc. Voyager is a trademark of ASA Electronics, LLC.
  
  
 </div>

Camera ready - C650 Air Cart

<div>
 
 The John Deere ultrasonic bin level sensing system will increase the accuracy of bin level read outs in the cab and on the cart side display compared to the paddle design. The accuracy of this system is within 10 percent of actual product in the tank. Product in the tank is measured utilizing high-frequency sound waves (ultrasonic) that are emitted from the unit and received back when they reverberate off the product in the tank. These sound waves generate a digital signal which can be mapped across the angle of repose for the product in the tank. Using calculus volume can be determined from the convex slope determined from the ultrasonic frequencies. When metering two products into one airstream, ultrasonic can improve the accuracy of detection up to 50 percent more than traditional paddle sensors.
 </div>

Ultrasonic bin level sensing

<div>
 
 The C650 Air Carts have five tank lids to make filling convenient and quick. The three back tank lids are operated by pushing forward on the foot pedal and straight down on the handle. The lid slides out of the way, contouring the shape of the tank, so it does not interfere with the conveyor. The tank lids seal tight by pulling upward on the handle and stepping back on the foot pedal. The three back tank lids offer a wide opening, making an easy job out of placing the conveyor in the right place during fills. The design is a single per tank design, providing for faster fill times.
 
 The front 1762-L (50-bu) tank has two options to make loading low rate products easier. If the grower is filling the tank with bags, the front lid is accessible from the lower platform of the cart. The two front railings of the cart can be removed to allow for a truck to bring bags directly to the platform. As pictured above, the bottom fill location of the front tank has a bag splitter.
  
 To fill the front tank with a conveyor, the top tank lid is easily reached with the hydraulic conveyance system.
 </div>

Specifications
First tank capacity	1761 L50 bu
Second tank capacity	9162 L260 bu
Third tank capacity	4581 L130 bu
Fourth tank capacity	7400 L210 bu
Drive type	Hydraulic
Maximum rpm	550 lb. of seed per acre at 5.5 mph and 15 degree slope (300 lb. fertilizer and 250 lb. seed)
Weight empty	16,594 kg36,583 lb
Tow behind	Tow-behind
Quantity	Four Tanks
First tank capacity	1761 L50 bu
Second tank capacity	9162 L260 bu
Third tank capacity	4581 L130 bu
Fourth tank capacity	7400 L210 bu
Drive type	Hydraulic
Metering system	Five meter cartridges; 30 approved crops
Rate	100 bu. per minute
Tube diameter	30.5 cm12 in.
Belt width	48.26 cm19 in.
Low profile hopper	183 cm X 76.2 cm X 23 cm72 in. X 30 in. X 9 in.
Air system type	B-type
Drive	Hydraulic
Air hose	Primary: Stainless-steel 3 in. (7.62 cm)
Maximum rpm	550 lb. of seed per acre at 5.5 mph and 15 degree slope (300 lb. fertilizer and 250 lb. seed)
Diameter	69.85 cm27.5 in.
Width	6.16 m20 ft. 2 in.
Height	Field - 16 ft. 3 in. (4.94 m)Transport - 13 ft. 4 in. (4.05 m)
Length	11.86 m38 ft. 11 in.
Weight empty	16,594 kg36,583 lb